patch-2.3.99-pre1 linux/drivers/ide/amd7409.c

• Lines: 412
• Date: Mon Feb 28 07:18:20 2000
• Orig file: v2.3.51/linux/drivers/ide/amd7409.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.3.51/linux/drivers/ide/amd7409.c linux/drivers/ide/amd7409.c
@@ -0,0 +1,411 @@
+/*
+ * linux/drivers/block/amd7409.c		Version 0.03	Feb. 10, 2000
+ *
+ * Copyright (C) 2000			Andre Hedrick <andre@suse.com>
+ * May be copied or modified under the terms of the GNU General Public License
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/hdreg.h>
+
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include "ide_modes.h"
+
+#define DISPLAY_VIPER_TIMINGS
+
+#if defined(DISPLAY_VIPER_TIMINGS) && defined(CONFIG_PROC_FS)
+#include <linux/stat.h>
+#include <linux/proc_fs.h>
+
+static int amd7409_get_info(char *, char **, off_t, int);
+extern int (*amd7409_display_info)(char *, char **, off_t, int); /* ide-proc.c */
+extern char *ide_media_verbose(ide_drive_t *);
+static struct pci_dev *bmide_dev;
+
+static int amd7409_get_info (char *buffer, char **addr, off_t offset, int count)
+{
+	char *p = buffer;
+	u32 bibma = bmide_dev->resource[4].start;
+	u8 c0 = 0, c1 = 0;
+
+	/*
+	 * at that point bibma+0x2 et bibma+0xa are byte registers
+	 * to investigate:
+	 */
+	c0 = inb_p((unsigned short)bibma + 0x02);
+	c1 = inb_p((unsigned short)bibma + 0x0a);
+
+	p += sprintf(p, "\n                                AMD 7409 VIPER Chipset.\n");
+	p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n");
+	p += sprintf(p, "                %sabled                         %sabled\n",
+			(c0&0x80) ? "dis" : " en",
+			(c1&0x80) ? "dis" : " en");
+	p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n");
+	p += sprintf(p, "DMA enabled:    %s              %s             %s               %s\n",
+			(c0&0x20) ? "yes" : "no ", (c0&0x40) ? "yes" : "no ",
+			(c1&0x20) ? "yes" : "no ", (c1&0x40) ? "yes" : "no " );
+	p += sprintf(p, "UDMA\n");
+	p += sprintf(p, "DMA\n");
+	p += sprintf(p, "PIO\n");
+
+	return p-buffer;	/* => must be less than 4k! */
+}
+#endif  /* defined(DISPLAY_VIPER_TIMINGS) && defined(CONFIG_PROC_FS) */
+
+byte amd7409_proc = 0;
+
+extern char *ide_xfer_verbose (byte xfer_rate);
+
+/*
+ * Here is where all the hard work goes to program the chipset.
+ *
+ */
+static int amd7409_tune_chipset (ide_drive_t *drive, byte speed)
+{
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= hwif->pci_dev;
+	int err			= 0;
+	byte unit		= (drive->select.b.unit & 0x01);
+	int drive_number	= ((HWIF(drive)->channel ? 2 : 0) + unit);
+	unsigned long dma_base	= hwif->dma_base;
+	byte drive_pci		= 0x00;
+	byte drive_pci2		= 0x00;
+	byte ultra_timing	= 0x00;
+	byte dma_pio_timing	= 0x00;
+	byte pio_timing		= 0x00;
+
+        switch (drive_number) {
+		case 0: drive_pci = 0x53; drive_pci2 = 0x4b; break;
+		case 1: drive_pci = 0x52; drive_pci2 = 0x4a; break;
+		case 2: drive_pci = 0x51; drive_pci2 = 0x49; break;
+		case 3: drive_pci = 0x50; drive_pci2 = 0x48; break;
+		default:
+                        return ((int) ide_dma_off_quietly);
+        }
+
+	pci_read_config_byte(dev, drive_pci, &ultra_timing);
+	pci_read_config_byte(dev, drive_pci2, &dma_pio_timing);
+	pci_read_config_byte(dev, 0x4c, &pio_timing);
+
+#ifdef DEBUG
+	printk("%s: UDMA 0x%02x DMAPIO 0x%02x PIO 0x%02x ",
+		drive->name, ultra_timing, dma_pio_timing, pio_timing);
+#endif
+
+	ultra_timing &= ~0xC7;
+	dma_pio_timing &= ~0xFF;
+	pio_timing &= ~(0x03 << drive_number);
+
+#ifdef DEBUG
+	printk(":: UDMA 0x%02x DMAPIO 0x%02x PIO 0x%02x ",
+		ultra_timing, dma_pio_timing, pio_timing);
+#endif
+
+	switch(speed) {
+		case XFER_UDMA_4:
+			ultra_timing |= 0x45;
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_UDMA_3:
+			ultra_timing |= 0x44;
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_UDMA_2:
+			ultra_timing |= 0x40;
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_UDMA_1:
+			ultra_timing |= 0x41;
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_UDMA_0:
+			ultra_timing |= 0x42;
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_MW_DMA_2:
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_MW_DMA_1:
+			dma_pio_timing |= 0x21;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_MW_DMA_0:
+			dma_pio_timing |= 0x77;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_PIO_4:
+			dma_pio_timing |= 0x20;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_PIO_3:
+			dma_pio_timing |= 0x22;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_PIO_2:
+			dma_pio_timing |= 0x42;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_PIO_1:
+			dma_pio_timing |= 0x65;
+			pio_timing |= (0x03 << drive_number);
+			break;
+		case XFER_PIO_0:
+		default:
+			dma_pio_timing |= 0xA8;
+			pio_timing |= (0x03 << drive_number);
+			break;
+        }
+
+	pci_write_config_byte(dev, drive_pci, ultra_timing);
+	pci_write_config_byte(dev, drive_pci2, dma_pio_timing);
+	pci_write_config_byte(dev, 0x4c, pio_timing);
+
+#ifdef DEBUG
+	printk(":: UDMA 0x%02x DMAPIO 0x%02x PIO 0x%02x\n",
+		ultra_timing, dma_pio_timing, pio_timing);
+#endif
+
+	if (speed > XFER_PIO_4) {
+		outb(inb(dma_base+2)|(1<<(5+unit)), dma_base+2);
+	} else {
+		outb(inb(dma_base+2) & ~(1<<(5+unit)), dma_base+2);
+	}
+	err = ide_config_drive_speed(drive, speed);
+	return (err);
+}
+
+/*
+ * This allows the configuration of ide_pci chipset registers
+ * for cards that learn about the drive's UDMA, DMA, PIO capabilities
+ * after the drive is reported by the OS.
+ */
+static int config_chipset_for_dma (ide_drive_t *drive)
+{
+	struct hd_driveid *id	= drive->id;
+	byte udma_66		= ((id->hw_config & 0x2000) &&
+				   (HWIF(drive)->udma_four)) ? 1 : 0;
+	byte speed		= 0x00;
+	int  rval;
+
+	if ((id->dma_ultra & 0x0010) && (udma_66)) {
+		speed = XFER_UDMA_4;
+	} else if ((id->dma_ultra & 0x0008) && (udma_66)) {
+		speed = XFER_UDMA_3;
+	} else if (id->dma_ultra & 0x0004) {
+		speed = XFER_UDMA_2;
+	} else if (id->dma_ultra & 0x0002) {
+		speed = XFER_UDMA_1;
+	} else if (id->dma_ultra & 0x0001) {
+		speed = XFER_UDMA_0;
+	} else if (id->dma_mword & 0x0004) {
+		speed = XFER_MW_DMA_2;
+	} else if (id->dma_mword & 0x0002) {
+		speed = XFER_MW_DMA_1;
+	} else if (id->dma_mword & 0x0001) {
+		speed = XFER_MW_DMA_0;
+        } else {
+		return ((int) ide_dma_off_quietly);
+	}
+
+	(void) amd7409_tune_chipset(drive, speed);
+
+	rval = (int)(	((id->dma_ultra >> 11) & 3) ? ide_dma_on :
+			((id->dma_ultra >> 8) & 7) ? ide_dma_on :
+			((id->dma_mword >> 8) & 7) ? ide_dma_on :
+						     ide_dma_off_quietly);
+
+	return rval;
+}
+
+static void config_chipset_for_pio (ide_drive_t *drive)
+{
+	unsigned short eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
+	unsigned short xfer_pio	= drive->id->eide_pio_modes;
+	byte			timing, speed, pio;
+
+	pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
+
+	if (xfer_pio> 4)
+		xfer_pio = 0;
+
+	if (drive->id->eide_pio_iordy > 0) {
+		for (xfer_pio = 5;
+			xfer_pio>0 &&
+			drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
+			xfer_pio--);
+	} else {
+		xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
+			   (drive->id->eide_pio_modes & 2) ? 0x04 :
+			   (drive->id->eide_pio_modes & 1) ? 0x03 :
+			   (drive->id->tPIO & 2) ? 0x02 :
+			   (drive->id->tPIO & 1) ? 0x01 : xfer_pio;
+	}
+
+	timing = (xfer_pio >= pio) ? xfer_pio : pio;
+
+	switch(timing) {
+		case 4: speed = XFER_PIO_4;break;
+		case 3: speed = XFER_PIO_3;break;
+		case 2: speed = XFER_PIO_2;break;
+		case 1: speed = XFER_PIO_1;break;
+		default:
+			speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
+			break;
+	}
+	(void) amd7409_tune_chipset(drive, speed);
+}
+
+static void amd7409_tune_drive (ide_drive_t *drive, byte pio)
+{
+	byte speed;
+	switch(pio) {
+		case 4:		speed = XFER_PIO_4;break;
+		case 3:		speed = XFER_PIO_3;break;
+		case 2:		speed = XFER_PIO_2;break;
+		case 1:		speed = XFER_PIO_1;break;
+		default:	speed = XFER_PIO_0;break;
+	}
+	(void) amd7409_tune_chipset(drive, speed);
+}
+
+static int config_drive_xfer_rate (ide_drive_t *drive)
+{
+	struct hd_driveid *id = drive->id;
+	ide_dma_action_t dma_func = ide_dma_on;
+
+	if (id && (id->capability & 1) && HWIF(drive)->autodma) {
+		/* Consult the list of known "bad" drives */
+		if (ide_dmaproc(ide_dma_bad_drive, drive)) {
+			dma_func = ide_dma_off;
+			goto fast_ata_pio;
+		}
+		dma_func = ide_dma_off_quietly;
+		if (id->field_valid & 4) {
+			if (id->dma_ultra & 0x001F) {
+				/* Force if Capable UltraDMA */
+				dma_func = config_chipset_for_dma(drive);
+				if ((id->field_valid & 2) &&
+				    (dma_func != ide_dma_on))
+					goto try_dma_modes;
+			}
+		} else if (id->field_valid & 2) {
+try_dma_modes:
+			if (id->dma_mword & 0x0007) {
+				/* Force if Capable regular DMA modes */
+				dma_func = config_chipset_for_dma(drive);
+				if (dma_func != ide_dma_on)
+					goto no_dma_set;
+			}
+		} else if (ide_dmaproc(ide_dma_good_drive, drive)) {
+			if (id->eide_dma_time > 150) {
+				goto no_dma_set;
+			}
+			/* Consult the list of known "good" drives */
+			dma_func = config_chipset_for_dma(drive);
+			if (dma_func != ide_dma_on)
+				goto no_dma_set;
+		} else {
+			goto fast_ata_pio;
+		}
+	} else if ((id->capability & 8) || (id->field_valid & 2)) {
+fast_ata_pio:
+		dma_func = ide_dma_off_quietly;
+no_dma_set:
+
+		config_chipset_for_pio(drive);
+	}
+	return HWIF(drive)->dmaproc(dma_func, drive);
+}
+
+/*
+ * amd7409_dmaproc() initiates/aborts (U)DMA read/write operations on a drive.
+ */
+
+int amd7409_dmaproc (ide_dma_action_t func, ide_drive_t *drive)
+{
+	switch (func) {
+		case ide_dma_check:
+			return config_drive_xfer_rate(drive);
+		default:
+			break;
+	}
+	return ide_dmaproc(func, drive);	/* use standard DMA stuff */
+}
+
+unsigned int __init pci_init_amd7409 (struct pci_dev *dev, const char *name)
+{
+	unsigned long fixdma_base = dev->resource[4].start;
+
+	if (!fixdma_base || fixdma_base == PCI_BASE_ADDRESS_IO_MASK) {
+		/*
+		 *
+		 */
+	} else {
+		/*
+		 * enable DMA capable bit, and "not" simplex only
+		 */
+		outb(inb(fixdma_base+2) & 0x60, fixdma_base+2);
+
+		if (inb(fixdma_base+2) & 0x80)
+			printk("%s: simplex device: DMA will fail!!\n", name);
+	}
+#if defined(DISPLAY_VIPER_TIMINGS) && defined(CONFIG_PROC_FS)
+	amd7409_proc = 1;
+	bmide_dev = dev;
+	amd7409_display_info = &amd7409_get_info;
+#endif /* DISPLAY_VIPER_TIMINGS && CONFIG_PROC_FS */
+
+	return 0;
+}
+
+unsigned int __init ata66_amd7409 (ide_hwif_t *hwif)
+{
+#ifdef CONFIG_AMD7409_OVERRIDE
+	byte ata66 = 1;
+#else
+	byte ata66 = 0;
+#endif /* CONFIG_AMD7409_OVERRIDE */
+
+#if 0
+	pci_read_config_byte(hwif->pci_dev, 0x48, &ata66);
+	return ((ata66 & 0x02) ? 0 : 1);
+#endif
+	return ata66;
+}
+
+void __init ide_init_amd7409 (ide_hwif_t *hwif)
+{
+	hwif->tuneproc = &amd7409_tune_drive;
+	if (hwif->dma_base) {
+		hwif->dmaproc = &amd7409_dmaproc;
+	} else {
+		hwif->autodma = 0;
+		hwif->drives[0].autotune = 1;
+		hwif->drives[1].autotune = 1;
+	}
+}
+
+void ide_dmacapable_amd7409 (ide_hwif_t *hwif, unsigned long dmabase)
+{
+	ide_setup_dma(hwif, dmabase, 8);
+}