patch-2.3.21 linux/drivers/char/pc_keyb.h

Next file: linux/drivers/char/ppdev.h
Previous file: linux/drivers/char/pc_keyb.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.3.20/linux/drivers/char/pc_keyb.h linux/drivers/char/pc_keyb.h
@@ -1,130 +0,0 @@
-/*
- *	linux/drivers/char/pc_keyb.h
- *
- *	PC Keyboard And Keyboard Controller
- *
- *	(c) 1997 Martin Mares <mj@atrey.karlin.mff.cuni.cz>
- */
-
-/*
- *	Configuration Switches
- */
-
-#undef KBD_REPORT_ERR			/* Report keyboard errors */
-#define KBD_REPORT_UNKN			/* Report unknown scan codes */
-#define KBD_REPORT_TIMEOUTS		/* Report keyboard timeouts */
-#undef KBD_IS_FOCUS_9000		/* We have the brain-damaged FOCUS-9000 keyboard */
-#undef INITIALIZE_MOUSE			/* Define if your PS/2 mouse needs initialization. */
-
-
-
-#define KBD_INIT_TIMEOUT 1000		/* Timeout in ms for initializing the keyboard */
-#define KBC_TIMEOUT 250			/* Timeout in ms for sending to keyboard controller */
-#define KBD_TIMEOUT 1000		/* Timeout in ms for keyboard command acknowledge */
-
-/*
- *	Internal variables of the driver
- */
-
-extern unsigned char pckbd_read_mask;
-extern unsigned char aux_device_present;
-
-/*
- *	Keyboard Controller Registers
- */
-
-#define KBD_STATUS_REG		0x64	/* Status register (R) */
-#define KBD_CNTL_REG		0x64	/* Controller command register (W) */
-#define KBD_DATA_REG		0x60	/* Keyboard data register (R/W) */
-
-/*
- *	Keyboard Controller Commands
- */
-
-#define KBD_CCMD_READ_MODE	0x20	/* Read mode bits */
-#define KBD_CCMD_WRITE_MODE	0x60	/* Write mode bits */
-#define KBD_CCMD_GET_VERSION	0xA1	/* Get controller version */
-#define KBD_CCMD_MOUSE_DISABLE	0xA7	/* Disable mouse interface */
-#define KBD_CCMD_MOUSE_ENABLE	0xA8	/* Enable mouse interface */
-#define KBD_CCMD_TEST_MOUSE	0xA9	/* Mouse interface test */
-#define KBD_CCMD_SELF_TEST	0xAA	/* Controller self test */
-#define KBD_CCMD_KBD_TEST	0xAB	/* Keyboard interface test */
-#define KBD_CCMD_KBD_DISABLE	0xAD	/* Keyboard interface disable */
-#define KBD_CCMD_KBD_ENABLE	0xAE	/* Keyboard interface enable */
-#define KBD_CCMD_WRITE_AUX_OBUF	0xD3    /* Write to output buffer as if
-					   initiated by the auxiliary device */
-#define KBD_CCMD_WRITE_MOUSE	0xD4	/* Write the following byte to the mouse */
-
-/*
- *	Keyboard Commands
- */
-
-#define KBD_CMD_SET_LEDS	0xED	/* Set keyboard leds */
-#define KBD_CMD_SET_RATE	0xF3	/* Set typematic rate */
-#define KBD_CMD_ENABLE		0xF4	/* Enable scanning */
-#define KBD_CMD_DISABLE		0xF5	/* Disable scanning */
-#define KBD_CMD_RESET		0xFF	/* Reset */
-
-/*
- *	Keyboard Replies
- */
-
-#define KBD_REPLY_POR		0xAA	/* Power on reset */
-#define KBD_REPLY_ACK		0xFA	/* Command ACK */
-#define KBD_REPLY_RESEND	0xFE	/* Command NACK, send the cmd again */
-
-/*
- *	Status Register Bits
- */
-
-#define KBD_STAT_OBF 		0x01	/* Keyboard output buffer full */
-#define KBD_STAT_IBF 		0x02	/* Keyboard input buffer full */
-#define KBD_STAT_SELFTEST	0x04	/* Self test successful */
-#define KBD_STAT_CMD		0x08	/* Last write was a command write (0=data) */
-#define KBD_STAT_UNLOCKED	0x10	/* Zero if keyboard locked */
-#define KBD_STAT_MOUSE_OBF	0x20	/* Mouse output buffer full */
-#define KBD_STAT_GTO 		0x40	/* General receive/xmit timeout */
-#define KBD_STAT_PERR 		0x80	/* Parity error */
-
-#define AUX_STAT_OBF (KBD_STAT_OBF | KBD_STAT_MOUSE_OBF)
-
-/*
- *	Controller Mode Register Bits
- */
-
-#define KBD_MODE_KBD_INT	0x01	/* Keyboard data generate IRQ1 */
-#define KBD_MODE_MOUSE_INT	0x02	/* Mouse data generate IRQ12 */
-#define KBD_MODE_SYS 		0x04	/* The system flag (?) */
-#define KBD_MODE_NO_KEYLOCK	0x08	/* The keylock doesn't affect the keyboard if set */
-#define KBD_MODE_DISABLE_KBD	0x10	/* Disable keyboard interface */
-#define KBD_MODE_DISABLE_MOUSE	0x20	/* Disable mouse interface */
-#define KBD_MODE_KCC 		0x40	/* Scan code conversion to PC format */
-#define KBD_MODE_RFU		0x80
-
-/*
- *	Mouse Commands
- */
-
-#define AUX_SET_RES		0xE8	/* Set resolution */
-#define AUX_SET_SCALE11		0xE6	/* Set 1:1 scaling */
-#define AUX_SET_SCALE21		0xE7	/* Set 2:1 scaling */
-#define AUX_GET_SCALE		0xE9	/* Get scaling factor */
-#define AUX_SET_STREAM		0xEA	/* Set stream mode */
-#define AUX_SET_SAMPLE		0xF3	/* Set sample rate */
-#define AUX_ENABLE_DEV		0xF4	/* Enable aux device */
-#define AUX_DISABLE_DEV		0xF5	/* Disable aux device */
-#define AUX_RESET		0xFF	/* Reset aux device */
-#define AUX_ACK			0xFA	/* Command byte ACK. */
-
-#define AUX_BUF_SIZE		2048	/* This might be better divisible by
-					   three to make overruns stay in sync
-					   but then the read function would need
-					   a lock etc - ick */
-
-struct aux_queue {
-	unsigned long head;
-	unsigned long tail;
-	wait_queue_head_t proc_list;
-	struct fasync_struct *fasync;
-	unsigned char buf[AUX_BUF_SIZE];
-};

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)