patch-2.0.37 linux/drivers/scsi/Config.in

• Lines: 73
• Date: Sun Jun 13 10:21:02 1999
• Orig file: v2.0.36/linux/drivers/scsi/Config.in
• Orig date: Sun Nov 15 21:51:46 1998

diff -u --recursive --new-file v2.0.36/linux/drivers/scsi/Config.in linux/drivers/scsi/Config.in
@@ -15,15 +15,14 @@
 comment 'SCSI low-level drivers'
 
 dep_tristate '7000FASST SCSI support' CONFIG_SCSI_7000FASST $CONFIG_SCSI
+dep_tristate 'ACARD SCSI support' CONFIG_SCSI_ACARD $CONFIG_SCSI
 dep_tristate 'Adaptec AHA152X/2825 support' CONFIG_SCSI_AHA152X $CONFIG_SCSI
 dep_tristate 'Adaptec AHA1542 support' CONFIG_SCSI_AHA1542 $CONFIG_SCSI
 dep_tristate 'Adaptec AHA1740 support' CONFIG_SCSI_AHA1740 $CONFIG_SCSI
 dep_tristate 'Adaptec AIC7xxx support' CONFIG_SCSI_AIC7XXX $CONFIG_SCSI
 if [ "$CONFIG_SCSI_AIC7XXX" != "n" ]; then
-    bool '   Override driver defaults for commands per LUN' CONFIG_OVERRIDE_CMDS N
-    if [ "$CONFIG_OVERRIDE_CMDS" != "n" ]; then
-      int  '   Maximum number of commands per LUN' CONFIG_AIC7XXX_CMDS_PER_LUN 24
-    fi
+    bool '   Enable Tagged Command Queueing (TCQ) by default' CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT
+    int  '   Maximum number of TCQ commands per device' CONFIG_AIC7XXX_CMDS_PER_DEVICE 8
     bool '   Collect statistics to report in /proc' CONFIG_AIC7XXX_PROC_STATS N
     int  '   Delay in seconds after SCSI bus reset' CONFIG_AIC7XXX_RESET_DELAY 5
 fi
@@ -52,7 +51,10 @@
 		"Port CONFIG_SCSI_G_NCR5380_PORT \
 		Memory CONFIG_SCSI_G_NCR5380_MEM" Port
 fi
+dep_tristate 'Initio 91XX support' CONFIG_SCSI_INITIO $CONFIG_SCSI
+dep_tristate 'Initio INI-A100U2W support' CONFIG_SCSI_INIA100 $CONFIG_SCSI
 dep_tristate 'NCR53c406a SCSI support' CONFIG_SCSI_NCR53C406A $CONFIG_SCSI
+dep_tristate 'symbios 53c416 SCSI support' CONFIG_SCSI_SYM53C416 $CONFIG_SCSI
 if [ "$CONFIG_PCI" = "y" ]; then
   dep_tristate 'NCR53c7,8xx SCSI support'  CONFIG_SCSI_NCR53C7xx $CONFIG_SCSI
   if [ "$CONFIG_SCSI_NCR53C7xx" != "n" ]; then
@@ -64,12 +66,12 @@
 if [ "$CONFIG_PCI" = "y" -a "$CONFIG_SCSI_NCR53C7xx" != "y" ]; then
   dep_tristate 'NCR53C8XX SCSI support' CONFIG_SCSI_NCR53C8XX $CONFIG_SCSI
   if [ "$CONFIG_SCSI_NCR53C8XX" != "n" ]; then
-    bool '  detect and read serial NVRAMs' CONFIG_SCSI_NCR53C8XX_NVRAM_DETECT
-    bool '  enable tagged command queueing' CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE
+    int  '  default tagged command queue depth' CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS 8
+    int  '  maximum number of queued commands' CONFIG_SCSI_NCR53C8XX_MAX_TAGS 32
+    int  '  synchronous transfers frequency in MHz' CONFIG_SCSI_NCR53C8XX_SYNC 20
+    bool '  enable profiling' CONFIG_SCSI_NCR53C8XX_PROFILE
     bool '  use normal IO' CONFIG_SCSI_NCR53C8XX_IOMAPPED
-    int  '  maximum number of queued commands' CONFIG_SCSI_NCR53C8XX_MAX_TAGS 4
-    int  '  synchronous transfers frequency in MHz' CONFIG_SCSI_NCR53C8XX_SYNC 5
-    if [ "$CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE" != "y" ]; then
+    if [ "$CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS" = "0" ]; then
       bool '  not allow targets to disconnect' CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
     fi
     if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
@@ -82,15 +84,22 @@
     bool '  Buggy EPP chipset support' CONFIG_SCSI_PPA_HAVE_PEDANTIC
 fi
 dep_tristate 'PAS16 SCSI support' CONFIG_SCSI_PAS16 $CONFIG_SCSI
+dep_tristate 'PCI-2000 support' CONFIG_SCSI_PCI2000 $CONFIG_SCSI
+dep_tristate 'PCI2220I support' CONFIG_SCSI_PCI2220I $CONFIG_SCSI
+dep_tristate 'PSI240I support' CONFIG_SCSI_PSI240I $CONFIG_SCSI
 dep_tristate 'Qlogic FAS SCSI support' CONFIG_SCSI_QLOGIC_FAS $CONFIG_SCSI
 if [ "$CONFIG_PCI" = "y" ]; then
   dep_tristate 'Qlogic ISP SCSI support' CONFIG_SCSI_QLOGIC_ISP $CONFIG_SCSI
 fi
 dep_tristate 'Seagate ST-02 and Future Domain TMC-8xx SCSI support' CONFIG_SCSI_SEAGATE $CONFIG_SCSI
-if [ "$CONFIG_PCI" = "y" -a "$CONFIG_SCSI_AM53C974" != "y" ]; then
-  dep_tristate 'Tekram DC-390(T) SCSI support' CONFIG_SCSI_DC390T $CONFIG_SCSI
+if [ "$CONFIG_PCI" = "y" ]; then
+  dep_tristate 'Tekram DC390(T) and Am53/79C974 SCSI support' CONFIG_SCSI_DC390T $CONFIG_SCSI
+  if [ "$CONFIG_SCSI_DC390T" != "n" ]; then
+    bool '  _omit_ support for non-DC390 adapters' CONFIG_SCSI_DC390T_NOGENSUPP
+  fi
 fi
 dep_tristate 'Trantor T128/T128F/T228 SCSI support' CONFIG_SCSI_T128 $CONFIG_SCSI
+dep_tristate 'Tripace TC-2550x SCSI support' CONFIG_SCSI_TC2550 $CONFIG_SCSI
 dep_tristate 'UltraStor 14F/34F support' CONFIG_SCSI_U14_34F $CONFIG_SCSI
   if [ "$CONFIG_SCSI_U14_34F" != "n" ]; then
     bool '  enable elevator sorting' CONFIG_SCSI_U14_34F_LINKED_COMMANDS