patch-2.0.34 linux/drivers/net/3c515.c

Next file: linux/drivers/net/3c59x.c
Previous file: linux/drivers/net/3c509.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.0.33/linux/drivers/net/3c515.c linux/drivers/net/3c515.c
@@ -0,0 +1,1502 @@
+/* 3c515.c: A 3Com ISA EtherLink XL "Corkscrew" ethernet driver for linux. */
+/*
+	Written 1997-1998 by Donald Becker.
+
+	This software may be used and distributed according to the terms
+	of the GNU Public License, incorporated herein by reference.
+
+	This driver is for the 3Com ISA EtherLink XL "Corkscrew" 3c515 ethercard.
+
+	The author may be reached as becker@CESDIS.gsfc.nasa.gov, or C/O
+	Center of Excellence in Space Data and Information Sciences
+	   Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771
+*/
+
+static char *version = "3c515.c:v0.99 4/7/98 becker@cesdis.gsfc.nasa.gov\n";
+#define CORKSCREW 1
+
+/* "Knobs" that adjust features and parameters. */
+/* Set the copy breakpoint for the copy-only-tiny-frames scheme.
+   Setting to > 1512 effectively disables this feature. */
+static const rx_copybreak = 200;
+/* Allow setting MTU to a larger size, bypassing the normal ethernet setup. */
+static const mtu = 1500;
+/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
+static int max_interrupt_work = 20;
+
+/* Enable the automatic media selection code -- usually set. */
+#define AUTOMEDIA 1
+
+/* Allow the use of fragment bus master transfers instead of only
+   programmed-I/O for Vortex cards.  Full-bus-master transfers are always
+   enabled by default on Boomerang cards.  If VORTEX_BUS_MASTER is defined,
+   the feature may be turned on using 'options'. */
+#define VORTEX_BUS_MASTER
+
+/* A few values that may be tweaked. */
+/* Keep the ring sizes a power of two for efficiency. */
+#define TX_RING_SIZE	16
+#define RX_RING_SIZE	16
+#define PKT_BUF_SZ		1536			/* Size of each temporary Rx buffer.*/
+
+#include <linux/config.h>
+#ifdef MODULE
+#ifdef MODVERSIONS
+#include <linux/modversions.h>
+#endif
+#include <linux/module.h>
+#include <linux/version.h>
+#else
+#define MOD_INC_USE_COUNT
+#define MOD_DEC_USE_COUNT
+#endif
+
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/ptrace.h>
+#include <linux/errno.h>
+#include <linux/in.h>
+#include <linux/ioport.h>
+#include <linux/malloc.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/bios32.h>
+#include <linux/timer.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <asm/dma.h>
+
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#if (LINUX_VERSION_CODE >= 0x10344)
+#define NEW_MULTICAST
+#include <linux/delay.h>
+#else
+#define udelay(microsec)	do { int _i = 4*microsec; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
+#endif
+
+/* Kernel version compatibility functions. */
+#define RUN_AT(x) (jiffies + (x))
+#define DEV_ALLOC_SKB(len) dev_alloc_skb(len + 2)
+
+#define FREE_IRQ(irqnum, dev) free_irq(irqnum, dev)
+#define REQUEST_IRQ(i,h,f,n, instance) request_irq(i,h,f,n, instance)
+#define IRQ(irq, dev_id, pt_regs) (irq, dev_id, pt_regs)
+
+#if (LINUX_VERSION_CODE < 0x20123)
+#define test_and_set_bit(val, addr) set_bit(val, addr)
+#elif defined(MODULE)
+MODULE_AUTHOR("Donald Becker <becker@cesdis.gsfc.nasa.gov>");
+MODULE_DESCRIPTION("3Com 3c515 Corkscrew driver");
+MODULE_PARM(debug, "i");
+MODULE_PARM(options, "1-" __MODULE_STRING(8) "i");
+MODULE_PARM(full_duplex, "1-" __MODULE_STRING(8) "i");
+MODULE_PARM(rx_copybreak, "i");
+MODULE_PARM(max_interrupt_work, "i");
+#endif
+
+/* "Knobs" for adjusting internal parameters. */
+/* Put out somewhat more debugging messages. (0 - no msg, 1 minimal msgs). */
+#define DRIVER_DEBUG 1
+/* Some values here only for performance evaluation and path-coverage
+   debugging. */
+static int rx_nocopy = 0, rx_copy = 0, queued_packet = 0;
+
+/* Number of times to check to see if the Tx FIFO has space, used in some
+   limited cases. */
+#define WAIT_TX_AVAIL 200
+
+/* Operational parameter that usually are not changed. */
+#define TX_TIMEOUT  40		/* Time in jiffies before concluding Tx hung */
+
+/* The size here is somewhat misleading: the Corkscrew also uses the ISA
+   aliased registers at <base>+0x400.
+   */
+#define CORKSCREW_TOTAL_SIZE 0x20
+
+#ifdef HAVE_DEVLIST
+struct netdev_entry tc515_drv =
+{"3c515", tc515_probe, CORKSCREW_TOTAL_SIZE, NULL};
+#endif
+
+#ifdef DRIVER_DEBUG
+int vortex_debug = DRIVER_DEBUG;
+#else
+int vortex_debug = 1;
+#endif
+
+#define CORKSCREW_ID 10
+
+/*
+				Theory of Operation
+
+I. Board Compatibility
+
+This device driver is designed for the 3Com 3c515 ISA Fast EtherLink XL,
+3Com's ISA bus adapter for Fast Ethernet.  Due to the unique I/O port layout,
+it's not practical to integrate this driver with the other EtherLink drivers.
+
+II. Board-specific settings
+
+The Corkscrew has an EEPROM for configuration, but no special settings are
+needed for Linux.
+
+III. Driver operation
+
+The 3c515 series use an interface that's very similar to the 3c900 "Boomerang"
+PCI cards, with the bus master interface extensively modified to work with
+the ISA bus.
+
+The card is capable of full-bus-master transfers with seperate
+lists of transmit and receive descriptors, similar to the AMD LANCE/PCnet,
+DEC Tulip and Intel Speedo3.
+
+This driver uses a "RX_COPYBREAK" scheme rather than a fixed intermediate
+receive buffer.  This scheme allocates full-sized skbuffs as receive
+buffers.  The value RX_COPYBREAK is used as the copying breakpoint: it is
+chosen to trade-off the memory wasted by passing the full-sized skbuff to
+the queue layer for all frames vs. the copying cost of copying a frame to a
+correctly-sized skbuff.
+
+
+IIIC. Synchronization
+The driver runs as two independent, single-threaded flows of control.  One
+is the send-packet routine, which enforces single-threaded use by the
+dev->tbusy flag.  The other thread is the interrupt handler, which is single
+threaded by the hardware and other software.
+
+IV. Notes
+
+Thanks to Terry Murphy of 3Com for providing documentation and a development
+board.
+
+The names "Vortex", "Boomerang" and "Corkscrew" are the internal 3Com
+project names.  I use these names to eliminate confusion -- 3Com product
+numbers and names are very similar and often confused.
+
+The new chips support both ethernet (1.5K) and FDDI (4.5K) frame sizes!
+This driver only supports ethernet frames because of the recent MTU limit
+of 1.5K, but the changes to support 4.5K are minimal.
+*/
+
+/* Operational definitions.
+   These are not used by other compilation units and thus are not
+   exported in a ".h" file.
+
+   First the windows.  There are eight register windows, with the command
+   and status registers available in each.
+   */
+#define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD)
+#define EL3_CMD 0x0e
+#define EL3_STATUS 0x0e
+
+/* The top five bits written to EL3_CMD are a command, the lower
+   11 bits are the parameter, if applicable.
+   Note that 11 parameters bits was fine for ethernet, but the new chips
+   can handle FDDI length frames (~4500 octets) and now parameters count
+   32-bit 'Dwords' rather than octets. */
+
+enum vortex_cmd {
+	TotalReset = 0<<11, SelectWindow = 1<<11, StartCoax = 2<<11,
+	RxDisable = 3<<11, RxEnable = 4<<11, RxReset = 5<<11,
+	UpStall = 6<<11, UpUnstall = (6<<11)+1,
+	DownStall = (6<<11)+2, DownUnstall = (6<<11)+3,
+	RxDiscard = 8<<11, TxEnable = 9<<11, TxDisable = 10<<11, TxReset = 11<<11,
+	FakeIntr = 12<<11, AckIntr = 13<<11, SetIntrEnb = 14<<11,
+	SetStatusEnb = 15<<11, SetRxFilter = 16<<11, SetRxThreshold = 17<<11,
+	SetTxThreshold = 18<<11, SetTxStart = 19<<11,
+	StartDMAUp = 20<<11, StartDMADown = (20<<11)+1, StatsEnable = 21<<11,
+	StatsDisable = 22<<11, StopCoax = 23<<11,};
+
+/* The SetRxFilter command accepts the following classes: */
+enum RxFilter {
+	RxStation = 1, RxMulticast = 2, RxBroadcast = 4, RxProm = 8 };
+
+/* Bits in the general status register. */
+enum vortex_status {
+	IntLatch = 0x0001, AdapterFailure = 0x0002, TxComplete = 0x0004,
+	TxAvailable = 0x0008, RxComplete = 0x0010, RxEarly = 0x0020,
+	IntReq = 0x0040, StatsFull = 0x0080,
+	DMADone = 1<<8, DownComplete = 1<<9, UpComplete = 1<<10,
+	DMAInProgress = 1<<11,			/* DMA controller is still busy.*/
+	CmdInProgress = 1<<12,			/* EL3_CMD is still busy.*/
+};
+
+/* Register window 1 offsets, the window used in normal operation.
+   On the Corkscrew this window is always mapped at offsets 0x10-0x1f. */
+enum Window1 {
+	TX_FIFO = 0x10,  RX_FIFO = 0x10,  RxErrors = 0x14,
+	RxStatus = 0x18,  Timer=0x1A, TxStatus = 0x1B,
+	TxFree = 0x1C, /* Remaining free bytes in Tx buffer. */
+};
+enum Window0 {
+  Wn0IRQ = 0x08,
+#if defined(CORKSCREW)
+	Wn0EepromCmd = 0x200A,		/* Corkscrew EEPROM command register. */
+	Wn0EepromData = 0x200C,		/* Corkscrew EEPROM results register. */
+#else
+	Wn0EepromCmd = 10,		/* Window 0: EEPROM command register. */
+	Wn0EepromData = 12,		/* Window 0: EEPROM results register. */
+#endif
+};
+enum Win0_EEPROM_bits {
+	EEPROM_Read = 0x80, EEPROM_WRITE = 0x40, EEPROM_ERASE = 0xC0,
+	EEPROM_EWENB = 0x30,		/* Enable erasing/writing for 10 msec. */
+	EEPROM_EWDIS = 0x00,		/* Disable EWENB before 10 msec timeout. */
+};
+/* EEPROM locations. */
+enum eeprom_offset {
+	PhysAddr01=0, PhysAddr23=1, PhysAddr45=2, ModelID=3,
+	EtherLink3ID=7, };
+
+enum Window3 {			/* Window 3: MAC/config bits. */
+	Wn3_Config=0, Wn3_MAC_Ctrl=6, Wn3_Options=8,
+};
+union wn3_config {
+	int i;
+	struct w3_config_fields {
+		unsigned int ram_size:3, ram_width:1, ram_speed:2, rom_size:2;
+		int pad8:8;
+		unsigned int ram_split:2, pad18:2, xcvr:3, pad21:1, autoselect:1;
+		int pad24:7;
+	} u;
+};
+
+enum Window4 {
+	Wn4_NetDiag = 6, Wn4_Media = 10,		/* Window 4: Xcvr/media bits. */
+};
+enum Win4_Media_bits {
+	Media_SQE = 0x0008,		/* Enable SQE error counting for AUI. */
+	Media_10TP = 0x00C0,	/* Enable link beat and jabber for 10baseT. */
+	Media_Lnk = 0x0080,		/* Enable just link beat for 100TX/100FX. */
+	Media_LnkBeat = 0x0800,
+};
+enum Window7 {					/* Window 7: Bus Master control. */
+	Wn7_MasterAddr = 0, Wn7_MasterLen = 6, Wn7_MasterStatus = 12,
+};
+/* Boomerang-style bus master control registers.  Note ISA aliases! */
+enum MasterCtrl {
+	PktStatus = 0x400, DownListPtr = 0x404, FragAddr = 0x408, FragLen = 0x40c,
+	TxFreeThreshold = 0x40f, UpPktStatus = 0x410, UpListPtr = 0x418,
+};
+
+/* The Rx and Tx descriptor lists.
+   Caution Alpha hackers: these types are 32 bits!  Note also the 8 byte
+   alignment contraint on tx_ring[] and rx_ring[]. */
+struct boom_rx_desc {
+	u32 next;
+	s32 status;
+	u32 addr;
+	s32 length;
+};
+/* Values for the Rx status entry. */
+enum rx_desc_status {
+	RxDComplete=0x00008000, RxDError=0x4000,
+	/* See boomerang_rx() for actual error bits */
+};
+
+struct boom_tx_desc {
+	u32 next;
+	s32 status;
+	u32 addr;
+	s32 length;
+};
+
+struct vortex_private {
+	char devname[8];			/* "ethN" string, also for kernel debug. */
+	const char *product_name;
+	struct device *next_module;
+	/* The Rx and Tx rings are here to keep them quad-word-aligned. */
+	struct boom_rx_desc rx_ring[RX_RING_SIZE];
+	struct boom_tx_desc tx_ring[TX_RING_SIZE];
+	/* The addresses of transmit- and receive-in-place skbuffs. */
+	struct sk_buff* rx_skbuff[RX_RING_SIZE];
+	struct sk_buff* tx_skbuff[TX_RING_SIZE];
+	unsigned int cur_rx, cur_tx;		/* The next free ring entry */
+	unsigned int dirty_rx, dirty_tx;	/* The ring entries to be free()ed. */
+	struct enet_statistics stats;
+	struct sk_buff *tx_skb;		/* Packet being eaten by bus master ctrl.  */
+	struct timer_list timer;	/* Media selection timer. */
+	int capabilities;			/* Adapter capabilities word. */
+	int options;				/* User-settable misc. driver options. */
+	int last_rx_packets;		/* For media autoselection. */
+	unsigned int available_media:8,	/* From Wn3_Options */
+	  media_override:3, 			/* Passed-in media type. */
+	  default_media:3,			/* Read from the EEPROM. */
+	  full_duplex:1, autoselect:1,
+	  bus_master:1,				/* Vortex can only do a fragment bus-m. */
+	  full_bus_master_tx:1, full_bus_master_rx:1, /* Boomerang  */
+      tx_full:1;
+};
+
+/* The action to take with a media selection timer tick.
+   Note that we deviate from the 3Com order by checking 10base2 before AUI.
+ */
+enum xcvr_types {
+	XCVR_10baseT=0, XCVR_AUI, XCVR_10baseTOnly, XCVR_10base2, XCVR_100baseTx,
+	XCVR_100baseFx, XCVR_MII=6, XCVR_Default=8,
+};
+
+static struct media_table {
+  char *name;
+  unsigned int media_bits:16,		/* Bits to set in Wn4_Media register. */
+	mask:8,				/* The transceiver-present bit in Wn3_Config.*/
+	next:8;				/* The media type to try next. */
+  short wait;			/* Time before we check media status. */
+} media_tbl[] = {
+  {	"10baseT",   Media_10TP,0x08, XCVR_10base2, (14*HZ)/10},
+  { "10Mbs AUI", Media_SQE, 0x20, XCVR_Default, (1*HZ)/10},
+  { "undefined", 0,			0x80, XCVR_10baseT, 10000},
+  { "10base2",   0,			0x10, XCVR_AUI,		(1*HZ)/10},
+  { "100baseTX", Media_Lnk, 0x02, XCVR_100baseFx, (14*HZ)/10},
+  { "100baseFX", Media_Lnk, 0x04, XCVR_MII,		(14*HZ)/10},
+  { "MII",		 0,			0x40, XCVR_10baseT, 3*HZ },
+  { "undefined", 0,			0x01, XCVR_10baseT, 10000},
+  { "Default",	 0,			0xFF, XCVR_10baseT, 10000},
+};
+
+static int vortex_scan(struct device *dev);
+static struct device *vortex_found_device(struct device *dev, int ioaddr,
+										  int irq, int product_index,
+										  int options);
+static int vortex_probe1(struct device *dev);
+static int vortex_open(struct device *dev);
+static void vortex_timer(unsigned long arg);
+static int vortex_start_xmit(struct sk_buff *skb, struct device *dev);
+static int vortex_rx(struct device *dev);
+static int boomerang_rx(struct device *dev);
+static void vortex_interrupt IRQ(int irq, void *dev_id, struct pt_regs *regs);
+static int vortex_close(struct device *dev);
+static void update_stats(int addr, struct device *dev);
+static struct enet_statistics *vortex_get_stats(struct device *dev);
+static void set_rx_mode(struct device *dev);
+
+
+/* Unlike the other PCI cards the 59x cards don't need a large contiguous
+   memory region, so making the driver a loadable module is feasible.
+
+   Unfortunately maximizing the shared code between the integrated and
+   module version of the driver results in a complicated set of initialization
+   procedures.
+   init_module() -- modules /  tc59x_init()  -- built-in
+		The wrappers for vortex_scan()
+   vortex_scan()  		 The common routine that scans for PCI and EISA cards
+   vortex_found_device() Allocate a device structure when we find a card.
+					Different versions exist for modules and built-in.
+   vortex_probe1()		Fill in the device structure -- this is separated
+					so that the modules code can put it in dev->init.
+*/
+/* This driver uses 'options' to pass the media type, full-duplex flag, etc. */
+/* Note: this is the only limit on the number of cards supported!! */
+static int options[8] = { -1, -1, -1, -1, -1, -1, -1, -1,};
+
+#ifdef MODULE
+static int debug = -1;
+/* A list of all installed Vortex devices, for removing the driver module. */
+static struct device *root_vortex_dev = NULL;
+
+int
+init_module(void)
+{
+	int cards_found;
+
+	if (debug >= 0)
+		vortex_debug = debug;
+	if (vortex_debug)
+		printk(version);
+
+	root_vortex_dev = NULL;
+	cards_found = vortex_scan(0);
+	return cards_found ? 0 : -ENODEV;
+}
+
+#else
+int tc515_probe(struct device *dev)
+{
+	int cards_found = 0;
+
+	cards_found = vortex_scan(dev);
+
+	if (vortex_debug > 0  &&  cards_found)
+		printk(version);
+
+	return cards_found ? 0 : -ENODEV;
+}
+#endif  /* not MODULE */
+
+static int vortex_scan(struct device *dev)
+{
+	int cards_found = 0;
+	static int ioaddr = 0x100;
+
+	/* Check all locations on the ISA bus -- evil! */
+	for (; ioaddr < 0x400; ioaddr += 0x20) {
+	  int irq;
+	  if (check_region(ioaddr, CORKSCREW_TOTAL_SIZE))
+		continue;
+	  /* Check the resource configuration for a matching ioaddr. */
+	  if ((inw(ioaddr + 0x2002) & 0x1f0) != (ioaddr & 0x1f0))
+		continue;
+	  /* Verify by reading the device ID from the EEPROM. */
+	  {
+		int timer;
+		outw(EEPROM_Read + 7, ioaddr + Wn0EepromCmd);
+		/* Pause for at least 162 us. for the read to take place. */
+		for (timer = 4; timer >= 0; timer--) {
+		  udelay(162);
+		  if ((inw(ioaddr + Wn0EepromCmd) & 0x0200) == 0)
+			break;
+		}
+		if (inw(ioaddr + Wn0EepromData) != 0x6d50)
+		  continue;
+	  }
+	  printk("3c515 Resource configuraiton register %#4.4x, DCR %4.4x.\n",
+			 inl(ioaddr + 0x2002), inw(ioaddr + 0x2000));
+	  irq = inw(ioaddr + 0x2002) & 15;
+	  vortex_found_device(dev, ioaddr, irq, CORKSCREW_ID, dev && dev->mem_start
+						  ? dev->mem_start : options[cards_found]);
+	  dev = 0;
+	  cards_found++;
+	}
+
+	if (vortex_debug)
+	  printk("%d 3c515 cards found.\n", cards_found);
+	return cards_found;
+}
+
+static struct device *vortex_found_device(struct device *dev, int ioaddr,
+										  int irq, int product_index,
+										  int options)
+{
+	struct vortex_private *vp;
+
+#ifdef MODULE
+	/* Allocate and fill new device structure. */
+	int dev_size = sizeof(struct device) +
+		sizeof(struct vortex_private) + 15;		/* Pad for alignment */
+	
+	dev = (struct device *) kmalloc(dev_size, GFP_KERNEL);
+	memset(dev, 0, dev_size);
+	/* Align the Rx and Tx ring entries.  */
+	dev->priv = (void *)(((long)dev + sizeof(struct device) + 15) & ~15);
+	vp = (struct vortex_private *)dev->priv;
+	dev->name = vp->devname; /* An empty string. */
+	dev->base_addr = ioaddr;
+	dev->irq = irq;
+	dev->dma = (product_index == CORKSCREW_ID ? inw(ioaddr + 0x2000) & 7 : 0);
+	dev->init = vortex_probe1;
+	vp->product_name = "3c515";
+	vp->options = options;
+	if (options >= 0) {
+		vp->media_override = ((options & 7) == 2)  ?  0  :  options & 7;
+		vp->full_duplex = (options & 8) ? 1 : 0;
+		vp->bus_master = (options & 16) ? 1 : 0;
+	} else {
+		vp->media_override = 7;
+		vp->full_duplex = 0;
+		vp->bus_master = 0;
+	}
+	ether_setup(dev);
+	vp->next_module = root_vortex_dev;
+	root_vortex_dev = dev;
+	if (register_netdev(dev) != 0)
+		return 0;
+#else  /* not a MODULE */
+	if (dev) {
+		/* Caution: quad-word alignment required for rings! */
+		dev->priv = kmalloc(sizeof (struct vortex_private), GFP_KERNEL);
+		memset(dev->priv, 0, sizeof (struct vortex_private));
+	}
+	dev = init_etherdev(dev, sizeof(struct vortex_private));
+	dev->base_addr = ioaddr;
+	dev->irq = irq;
+	dev->dma = (product_index == CORKSCREW_ID ? inw(ioaddr + 0x2000) & 7 : 0);
+	vp  = (struct vortex_private *)dev->priv;
+	vp->product_name = "3c515";
+	vp->options = options;
+	if (options >= 0) {
+		vp->media_override = ((options & 7) == 2)  ?  0  :  options & 7;
+		vp->full_duplex = (options & 8) ? 1 : 0;
+		vp->bus_master = (options & 16) ? 1 : 0;
+	} else {
+		vp->media_override = 7;
+		vp->full_duplex = 0;
+		vp->bus_master = 0;
+	}
+
+	vortex_probe1(dev);
+#endif /* MODULE */
+	return dev;
+}
+
+static int vortex_probe1(struct device *dev)
+{
+	int ioaddr = dev->base_addr;
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	unsigned int eeprom[0x40], checksum = 0;		/* EEPROM contents */
+	int i;
+
+	printk("%s: 3Com %s at %#3x,", dev->name,
+		   vp->product_name, ioaddr);
+
+	/* Read the station address from the EEPROM. */
+	EL3WINDOW(0);
+	for (i = 0; i < 0x18; i++) {
+		short *phys_addr = (short *)dev->dev_addr;
+		int timer;
+		outw(EEPROM_Read + i, ioaddr + Wn0EepromCmd);
+		/* Pause for at least 162 us. for the read to take place. */
+		for (timer = 4; timer >= 0; timer--) {
+			udelay(162);
+			if ((inw(ioaddr + Wn0EepromCmd) & 0x0200) == 0)
+				break;
+		}
+		eeprom[i] = inw(ioaddr + Wn0EepromData);
+		checksum ^= eeprom[i];
+		if (i < 3)
+			phys_addr[i] = htons(eeprom[i]);
+	}
+	checksum = (checksum ^ (checksum >> 8)) & 0xff;
+	if (checksum != 0x00)
+		printk(" ***INVALID CHECKSUM %4.4x*** ", checksum);
+	for (i = 0; i < 6; i++)
+		printk("%c%2.2x", i ? ':' : ' ', dev->dev_addr[i]);
+	if (eeprom[16] == 0x11c7) { 		/* Corkscrew */
+	  if (request_dma(dev->dma, "3c515")) {
+		printk(", DMA %d allocation failed", dev->dma);
+		dev->dma = 0;
+	  } else 
+		printk(", DMA %d", dev->dma);
+	}
+	printk(", IRQ %d\n", dev->irq);
+	/* Tell them about an invalid IRQ. */
+	if (vortex_debug && (dev->irq <= 0 || dev->irq > 15))
+		printk(" *** Warning: this IRQ is unlikely to work! ***\n");
+
+	{
+		char *ram_split[] = {"5:3", "3:1", "1:1", "3:5"};
+		union wn3_config config;
+		EL3WINDOW(3);
+		vp->available_media = inw(ioaddr + Wn3_Options);
+		config.i = inl(ioaddr + Wn3_Config);
+		if (vortex_debug > 1)
+			printk("  Internal config register is %4.4x, transceivers %#x.\n",
+				   config.i, inw(ioaddr + Wn3_Options));
+		printk("  %dK %s-wide RAM %s Rx:Tx split, %s%s interface.\n",
+			   8 << config.u.ram_size,
+			   config.u.ram_width ? "word" : "byte",
+			   ram_split[config.u.ram_split],
+			   config.u.autoselect ? "autoselect/" : "",
+			   media_tbl[config.u.xcvr].name);
+		dev->if_port = config.u.xcvr;
+		vp->default_media = config.u.xcvr;
+		vp->autoselect = config.u.autoselect;
+	}
+	if (vp->media_override != 7) {
+		printk("  Media override to transceiver type %d (%s).\n",
+			   vp->media_override, media_tbl[vp->media_override].name);
+		dev->if_port = vp->media_override;
+	}
+
+	vp->capabilities = eeprom[16];
+	vp->full_bus_master_tx = (vp->capabilities & 0x20) ? 1 : 0;
+	/* Rx is broken at 10mbps, so we always disable it. */
+	/* vp->full_bus_master_rx = 0;*/
+	vp->full_bus_master_rx = (vp->capabilities & 0x20) ? 1 : 0;
+
+	/* We do a request_region() to register /proc/ioports info. */
+	request_region(ioaddr, CORKSCREW_TOTAL_SIZE, vp->product_name);
+
+	/* The 3c59x-specific entries in the device structure. */
+	dev->open = &vortex_open;
+	dev->hard_start_xmit = &vortex_start_xmit;
+	dev->stop = &vortex_close;
+	dev->get_stats = &vortex_get_stats;
+	dev->set_multicast_list = &set_rx_mode;
+
+	return 0;
+}
+
+
+static int
+vortex_open(struct device *dev)
+{
+	int ioaddr = dev->base_addr;
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	union wn3_config config;
+	int i;
+
+	/* Before initializing select the active media port. */
+	EL3WINDOW(3);
+	if (vp->full_duplex)
+		outb(0x20, ioaddr + Wn3_MAC_Ctrl); /* Set the full-duplex bit. */
+	config.i = inl(ioaddr + Wn3_Config);
+
+	if (vp->media_override != 7) {
+		if (vortex_debug > 1)
+			printk("%s: Media override to transceiver %d (%s).\n",
+				   dev->name, vp->media_override,
+				   media_tbl[vp->media_override].name);
+		dev->if_port = vp->media_override;
+	} else if (vp->autoselect) {
+		/* Find first available media type, starting with 100baseTx. */
+		dev->if_port = 4;
+		while (! (vp->available_media & media_tbl[dev->if_port].mask))
+			dev->if_port = media_tbl[dev->if_port].next;
+
+		if (vortex_debug > 1)
+			printk("%s: Initial media type %s.\n",
+				   dev->name, media_tbl[dev->if_port].name);
+
+		init_timer(&vp->timer);
+		vp->timer.expires = RUN_AT(media_tbl[dev->if_port].wait);
+		vp->timer.data = (unsigned long)dev;
+		vp->timer.function = &vortex_timer;    /* timer handler */
+		add_timer(&vp->timer);
+	} else
+		dev->if_port = vp->default_media;
+
+	config.u.xcvr = dev->if_port;
+	outl(config.i, ioaddr + Wn3_Config);
+
+	if (vortex_debug > 1) {
+		printk("%s: vortex_open() InternalConfig %8.8x.\n",
+			dev->name, config.i);
+	}
+
+	outw(TxReset, ioaddr + EL3_CMD);
+	for (i = 20; i >= 0 ; i--)
+		if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+			break;
+
+	outw(RxReset, ioaddr + EL3_CMD);
+	/* Wait a few ticks for the RxReset command to complete. */
+	for (i = 20; i >= 0 ; i--)
+		if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+			break;
+
+	outw(SetStatusEnb | 0x00, ioaddr + EL3_CMD);
+
+	/* Use the now-standard shared IRQ implementation. */
+	if (vp->capabilities == 0x11c7) {
+	  /* Corkscrew: Cannot share ISA resources. */
+	  if (dev->irq == 0
+		  || dev->dma == 0
+		  || request_irq(dev->irq, &vortex_interrupt, 0,
+						 vp->product_name, dev))
+		return -EAGAIN;
+	  enable_dma(dev->dma);
+	  set_dma_mode(dev->dma, DMA_MODE_CASCADE);
+	} else if (request_irq(dev->irq, &vortex_interrupt, SA_SHIRQ,
+						   vp->product_name, dev)) {
+	  return -EAGAIN;
+	}
+
+	if (vortex_debug > 1) {
+		EL3WINDOW(4);
+		printk("%s: vortex_open() irq %d media status %4.4x.\n",
+			   dev->name, dev->irq, inw(ioaddr + Wn4_Media));
+	}
+
+	/* Set the station address and mask in window 2 each time opened. */
+	EL3WINDOW(2);
+	for (i = 0; i < 6; i++)
+		outb(dev->dev_addr[i], ioaddr + i);
+	for (; i < 12; i+=2)
+		outw(0, ioaddr + i);
+
+	if (dev->if_port == 3)
+		/* Start the thinnet transceiver. We should really wait 50ms...*/
+		outw(StartCoax, ioaddr + EL3_CMD);
+	EL3WINDOW(4);
+	outw((inw(ioaddr + Wn4_Media) & ~(Media_10TP|Media_SQE)) |
+		 media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
+
+	/* Switch to the stats window, and clear all stats by reading. */
+	outw(StatsDisable, ioaddr + EL3_CMD);
+	EL3WINDOW(6);
+	for (i = 0; i < 10; i++)	
+		inb(ioaddr + i);
+	inw(ioaddr + 10);
+	inw(ioaddr + 12);
+	/* New: On the Vortex we must also clear the BadSSD counter. */
+	EL3WINDOW(4);
+	inb(ioaddr + 12);
+	/* ..and on the Boomerang we enable the extra statistics bits. */
+	outw(0x0040, ioaddr + Wn4_NetDiag);
+
+	/* Switch to register set 7 for normal use. */
+	EL3WINDOW(7);
+
+	if (vp->full_bus_master_rx) { /* Boomerang bus master. */
+		vp->cur_rx = vp->dirty_rx = 0;
+		if (vortex_debug > 2)
+			printk("%s:  Filling in the Rx ring.\n", dev->name);
+		for (i = 0; i < RX_RING_SIZE; i++) {
+			struct sk_buff *skb;
+			if (i < (RX_RING_SIZE - 1))
+			  vp->rx_ring[i].next = virt_to_bus(&vp->rx_ring[i+1]);
+			else
+			  vp->rx_ring[i].next = 0;
+			vp->rx_ring[i].status = 0;	/* Clear complete bit. */
+			vp->rx_ring[i].length = PKT_BUF_SZ | 0x80000000;
+			skb = dev_alloc_skb(PKT_BUF_SZ);
+			vp->rx_skbuff[i] = skb;
+			if (skb == NULL)
+				break;			/* Bad news!  */
+			skb->dev = dev;			/* Mark as being used by this device. */
+			skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
+			vp->rx_ring[i].addr = virt_to_bus(skb->tail);
+		}
+		vp->rx_ring[i-1].next = virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */
+		outl(virt_to_bus(&vp->rx_ring[0]), ioaddr + UpListPtr);
+	}
+	if (vp->full_bus_master_tx) { 		/* Boomerang bus master Tx. */
+		vp->cur_tx = vp->dirty_tx = 0;
+		outb(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold); /* Room for a packet. */
+		/* Clear the Tx ring. */
+		for (i = 0; i < TX_RING_SIZE; i++)
+			vp->tx_skbuff[i] = 0;
+		outl(0, ioaddr + DownListPtr);
+	}
+	/* Set reciever mode: presumably accept b-case and phys addr only. */
+	set_rx_mode(dev);
+	outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
+
+	dev->tbusy = 0;
+	dev->interrupt = 0;
+	dev->start = 1;
+
+	outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
+	outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
+	/* Allow status bits to be seen. */
+	outw(SetStatusEnb | AdapterFailure|IntReq|StatsFull | 
+		 (vp->full_bus_master_tx ? DownComplete : TxAvailable) |
+		 (vp->full_bus_master_rx ? UpComplete : RxComplete) | 
+		 (vp->bus_master ? DMADone : 0),
+		 ioaddr + EL3_CMD);
+	/* Ack all pending events, and set active indicator mask. */
+	outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
+		 ioaddr + EL3_CMD);
+	outw(SetIntrEnb | IntLatch | TxAvailable | RxComplete | StatsFull
+		 | (vp->bus_master ? DMADone : 0) | UpComplete | DownComplete,
+			ioaddr + EL3_CMD);
+
+	MOD_INC_USE_COUNT;
+
+	return 0;
+}
+
+static void vortex_timer(unsigned long data)
+{
+#ifdef AUTOMEDIA
+	struct device *dev = (struct device *)data;
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	int ioaddr = dev->base_addr;
+	unsigned long flags;
+	int ok = 0;
+
+	if (vortex_debug > 1)
+		printk("%s: Media selection timer tick happened, %s.\n",
+			   dev->name, media_tbl[dev->if_port].name);
+
+	save_flags(flags);	cli(); {
+	  int old_window = inw(ioaddr + EL3_CMD) >> 13;
+	  int media_status;
+	  EL3WINDOW(4);
+	  media_status = inw(ioaddr + Wn4_Media);
+	  switch (dev->if_port) {
+	  case 0:  case 4:  case 5:		/* 10baseT, 100baseTX, 100baseFX  */
+		if (media_status & Media_LnkBeat) {
+		  ok = 1;
+		  if (vortex_debug > 1)
+			printk("%s: Media %s has link beat, %x.\n",
+				   dev->name, media_tbl[dev->if_port].name, media_status);
+		} else if (vortex_debug > 1)
+		  printk("%s: Media %s is has no link beat, %x.\n",
+				   dev->name, media_tbl[dev->if_port].name, media_status);
+ 
+		break;
+	  default:					/* Other media types handled by Tx timeouts. */
+		if (vortex_debug > 1)
+		  printk("%s: Media %s is has no indication, %x.\n",
+				 dev->name, media_tbl[dev->if_port].name, media_status);
+		ok = 1;
+	  }
+	  if ( ! ok) {
+		union wn3_config config;
+
+		do {
+			dev->if_port = media_tbl[dev->if_port].next;
+		} while ( ! (vp->available_media & media_tbl[dev->if_port].mask));
+		if (dev->if_port == 8) { /* Go back to default. */
+		  dev->if_port = vp->default_media;
+		  if (vortex_debug > 1)
+			printk("%s: Media selection failing, using default %s port.\n",
+				   dev->name, media_tbl[dev->if_port].name);
+		} else {
+		  if (vortex_debug > 1)
+			printk("%s: Media selection failed, now trying %s port.\n",
+				   dev->name, media_tbl[dev->if_port].name);
+		  vp->timer.expires = RUN_AT(media_tbl[dev->if_port].wait);
+		  add_timer(&vp->timer);
+		}
+		outw((media_status & ~(Media_10TP|Media_SQE)) |
+			 media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
+
+		EL3WINDOW(3);
+		config.i = inl(ioaddr + Wn3_Config);
+		config.u.xcvr = dev->if_port;
+		outl(config.i, ioaddr + Wn3_Config);
+
+		outw(dev->if_port == 3 ? StartCoax : StopCoax, ioaddr + EL3_CMD);
+	  }
+	  EL3WINDOW(old_window);
+	}   restore_flags(flags);
+	if (vortex_debug > 1)
+	  printk("%s: Media selection timer finished, %s.\n",
+			 dev->name, media_tbl[dev->if_port].name);
+
+#endif /* AUTOMEDIA*/
+	return;
+}
+
+static int
+vortex_start_xmit(struct sk_buff *skb, struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	int ioaddr = dev->base_addr;
+
+	if (dev->tbusy) {
+		int tickssofar = jiffies - dev->trans_start;
+		int i;
+
+		/* Min. wait before assuming a Tx failed == 400ms. */
+
+		if (tickssofar < 400*HZ/1000)		/* We probably aren't empty. */
+			return 1;
+		printk("%s: transmit timed out, tx_status %2.2x status %4.4x.\n",
+			   dev->name, inb(ioaddr + TxStatus),
+			   inw(ioaddr + EL3_STATUS));
+		/* Slight code bloat to be user friendly. */
+		if ((inb(ioaddr + TxStatus) & 0x88) == 0x88)
+			printk("%s: Transmitter encountered 16 collisions -- network"
+				   " network cable problem?\n", dev->name);
+#ifndef final_version
+		printk("  Flags; bus-master %d, full %d; dirty %d current %d.\n",
+			   vp->full_bus_master_tx, vp->tx_full, vp->dirty_tx, vp->cur_tx);
+		printk("  Down list %8.8x vs. %p.\n", inl(ioaddr + DownListPtr),
+			   &vp->tx_ring[0]);
+		for (i = 0; i < TX_RING_SIZE; i++) {
+			printk("  %d: %p  length %8.8x status %8.8x\n", i,
+				   &vp->tx_ring[i],
+				   vp->tx_ring[i].length,
+				   vp->tx_ring[i].status);
+		}
+#endif
+		/* Issue TX_RESET and TX_START commands. */
+		outw(TxReset, ioaddr + EL3_CMD);
+		for (i = 20; i >= 0 ; i--)
+			if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+				break;
+		outw(TxEnable, ioaddr + EL3_CMD);
+		dev->trans_start = jiffies;
+		/* dev->tbusy = 0;*/
+		vp->stats.tx_errors++;
+		vp->stats.tx_dropped++;
+		return 0;			/* Yes, silently *drop* the packet! */
+	}
+
+	/* Block a timer-based transmit from overlapping.  This could better be
+	   done with atomic_swap(1, dev->tbusy), but set_bit() works as well.
+	   If this ever occurs the queue layer is doing something evil! */
+	if (test_and_set_bit(0, (void*)&dev->tbusy) != 0) {
+		printk("%s: Transmitter access conflict.\n", dev->name);
+		return 1;
+	}
+
+	if (vp->full_bus_master_tx) { /* BOOMERANG bus-master */
+		/* Calculate the next Tx descriptor entry. */
+		int entry = vp->cur_tx % TX_RING_SIZE;
+		struct boom_tx_desc *prev_entry;
+		unsigned long flags, i;
+
+		if (vp->tx_full) /* No room to transmit with */
+		  return 1;
+		if (vp->cur_tx != 0)
+		  prev_entry = &vp->tx_ring[(vp->cur_tx-1) % TX_RING_SIZE];
+		else
+		  prev_entry = NULL;
+		if (vortex_debug > 3)
+			printk("%s: Trying to send a packet, Tx index %d.\n",
+				   dev->name, vp->cur_tx);
+		/* vp->tx_full = 1; */
+		vp->tx_skbuff[entry] = skb;
+		vp->tx_ring[entry].next = 0;
+		vp->tx_ring[entry].addr = virt_to_bus(skb->data);
+		vp->tx_ring[entry].length = skb->len | 0x80000000;
+		vp->tx_ring[entry].status = skb->len | 0x80000000;
+
+		save_flags(flags);
+		cli();
+		outw(DownStall, ioaddr + EL3_CMD);
+		/* Wait for the stall to complete. */
+		for (i = 20; i >= 0 ; i--)
+			if ( (inw(ioaddr + EL3_STATUS) & CmdInProgress) == 0)
+				break;
+		if (prev_entry)
+		  prev_entry->next = virt_to_bus(&vp->tx_ring[entry]);
+		if (inl(ioaddr + DownListPtr) == 0) {
+			outl(virt_to_bus(&vp->tx_ring[entry]), ioaddr + DownListPtr);
+			queued_packet++;
+		}
+		outw(DownUnstall, ioaddr + EL3_CMD);
+		restore_flags(flags);
+
+		vp->cur_tx++;
+		if (vp->cur_tx - vp->dirty_tx > TX_RING_SIZE - 1)
+			vp->tx_full = 1;
+		else {					/* Clear previous interrupt enable. */
+		  if (prev_entry)
+			prev_entry->status &= ~0x80000000;
+		  dev->tbusy = 0;
+		}
+		dev->trans_start = jiffies;
+		return 0;
+	}
+	/* Put out the doubleword header... */
+	outl(skb->len, ioaddr + TX_FIFO);
+#ifdef VORTEX_BUS_MASTER
+	if (vp->bus_master) {
+		/* Set the bus-master controller to transfer the packet. */
+		outl((int)(skb->data), ioaddr + Wn7_MasterAddr);
+		outw((skb->len + 3) & ~3, ioaddr + Wn7_MasterLen);
+		vp->tx_skb = skb;
+		outw(StartDMADown, ioaddr + EL3_CMD);
+		/* dev->tbusy will be cleared at the DMADone interrupt. */
+	} else {
+		/* ... and the packet rounded to a doubleword. */
+		outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
+		dev_kfree_skb (skb, FREE_WRITE);
+		if (inw(ioaddr + TxFree) > 1536) {
+			dev->tbusy = 0;
+		} else
+			/* Interrupt us when the FIFO has room for max-sized packet. */
+			outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
+	}
+#else
+	/* ... and the packet rounded to a doubleword. */
+	outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
+	dev_kfree_skb (skb, FREE_WRITE);
+	if (inw(ioaddr + TxFree) > 1536) {
+		dev->tbusy = 0;
+	} else
+		/* Interrupt us when the FIFO has room for max-sized packet. */
+		outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
+#endif  /* bus master */
+
+	dev->trans_start = jiffies;
+
+	/* Clear the Tx status stack. */
+	{
+		short tx_status;
+		int i = 4;
+
+		while (--i > 0	&&	(tx_status = inb(ioaddr + TxStatus)) > 0) {
+			if (tx_status & 0x3C) {		/* A Tx-disabling error occurred.  */
+				if (vortex_debug > 2)
+				  printk("%s: Tx error, status %2.2x.\n",
+						 dev->name, tx_status);
+				if (tx_status & 0x04) vp->stats.tx_fifo_errors++;
+				if (tx_status & 0x38) vp->stats.tx_aborted_errors++;
+				if (tx_status & 0x30) {
+					int j;
+					outw(TxReset, ioaddr + EL3_CMD);
+					for (j = 20; j >= 0 ; j--)
+						if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+							break;
+				}
+				outw(TxEnable, ioaddr + EL3_CMD);
+			}
+			outb(0x00, ioaddr + TxStatus); /* Pop the status stack. */
+		}
+	}
+	return 0;
+}
+
+/* The interrupt handler does all of the Rx thread work and cleans up
+   after the Tx thread. */
+static void vortex_interrupt IRQ(int irq, void *dev_id, struct pt_regs *regs)
+{
+	/* Use the now-standard shared IRQ implementation. */
+	struct device *dev = dev_id;
+	struct vortex_private *lp;
+	int ioaddr, status;
+	int latency;
+	int i = max_interrupt_work;
+
+	if (test_and_set_bit(0, (void*)&dev->interrupt)) {
+		printk("%s: Re-entering the interrupt handler.\n", dev->name);
+		return;
+	}
+
+	ioaddr = dev->base_addr;
+	latency = inb(ioaddr + Timer);
+	lp = (struct vortex_private *)dev->priv;
+
+	status = inw(ioaddr + EL3_STATUS);
+
+	if (vortex_debug > 4)
+		printk("%s: interrupt, status %4.4x, timer %d.\n", dev->name,
+			   status, latency);
+	if ((status & 0xE000) != 0xE000) {
+		static int donedidthis=0;
+		/* Some interrupt controllers store a bogus interrupt from boot-time.
+		   Ignore a single early interrupt, but don't hang the machine for
+		   other interrupt problems. */
+		if (donedidthis++ > 100) {
+			printk("%s: Bogus interrupt, bailing. Status %4.4x, start=%d.\n",
+				   dev->name, status, dev->start);
+			FREE_IRQ(dev->irq, dev);
+		}
+	}
+
+	do {
+		if (vortex_debug > 5)
+				printk("%s: In interrupt loop, status %4.4x.\n",
+					   dev->name, status);
+		if (status & RxComplete)
+			vortex_rx(dev);
+
+		if (status & TxAvailable) {
+			if (vortex_debug > 5)
+				printk("	TX room bit was handled.\n");
+			/* There's room in the FIFO for a full-sized packet. */
+			outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
+			dev->tbusy = 0;
+			mark_bh(NET_BH);
+		}
+		if (status & DownComplete) {
+			unsigned int dirty_tx = lp->dirty_tx;
+
+			while (lp->cur_tx - dirty_tx > 0) {
+				int entry = dirty_tx % TX_RING_SIZE;
+				if (inl(ioaddr + DownListPtr) ==
+					virt_to_bus(&lp->tx_ring[entry]))
+					break;			/* It still hasn't been processed. */
+				if (lp->tx_skbuff[entry]) {
+					dev_kfree_skb(lp->tx_skbuff[entry], FREE_WRITE);
+					lp->tx_skbuff[entry] = 0;
+				}
+				dirty_tx++;
+			}
+			lp->dirty_tx = dirty_tx;
+			outw(AckIntr | DownComplete, ioaddr + EL3_CMD);
+			if (lp->tx_full && (lp->cur_tx - dirty_tx <= TX_RING_SIZE - 1)) {
+				lp->tx_full= 0;
+				dev->tbusy = 0;
+				mark_bh(NET_BH);
+			}
+		}
+#ifdef VORTEX_BUS_MASTER
+		if (status & DMADone) {
+			outw(0x1000, ioaddr + Wn7_MasterStatus); /* Ack the event. */
+			dev->tbusy = 0;
+			dev_kfree_skb (lp->tx_skb, FREE_WRITE); /* Release the transfered buffer */
+			mark_bh(NET_BH);
+		}
+#endif
+		if (status & UpComplete) {
+			boomerang_rx(dev);
+			outw(AckIntr | UpComplete, ioaddr + EL3_CMD);
+		}
+		if (status & (AdapterFailure | RxEarly | StatsFull)) {
+			/* Handle all uncommon interrupts at once. */
+			if (status & RxEarly) {				/* Rx early is unused. */
+				vortex_rx(dev);
+				outw(AckIntr | RxEarly, ioaddr + EL3_CMD);
+			}
+			if (status & StatsFull) { 	/* Empty statistics. */
+				static int DoneDidThat = 0;
+				if (vortex_debug > 4)
+					printk("%s: Updating stats.\n", dev->name);
+				update_stats(ioaddr, dev);
+				/* DEBUG HACK: Disable statistics as an interrupt source. */
+				/* This occurs when we have the wrong media type! */
+				if (DoneDidThat == 0  &&
+					inw(ioaddr + EL3_STATUS) & StatsFull) {
+					int win, reg;
+					printk("%s: Updating stats failed, disabling stats as an"
+						   " interrupt source.\n", dev->name);
+					for (win = 0; win < 8; win++) {
+						EL3WINDOW(win);
+						printk("\n Vortex window %d:", win);
+						for (reg = 0; reg < 16; reg++)
+							printk(" %2.2x", inb(ioaddr+reg));
+					}
+					EL3WINDOW(7);
+					outw(SetIntrEnb | TxAvailable | RxComplete | AdapterFailure
+						 | UpComplete | DownComplete | TxComplete,
+						 ioaddr + EL3_CMD);
+					DoneDidThat++;
+				}
+			}
+			if (status & AdapterFailure) {
+				/* Adapter failure requires Rx reset and reinit. */
+				outw(RxReset, ioaddr + EL3_CMD);
+				/* Set the Rx filter to the current state. */
+				set_rx_mode(dev);
+				outw(RxEnable, ioaddr + EL3_CMD); /* Re-enable the receiver. */
+				outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD);
+			}
+		}
+
+		if (--i < 0) {
+			printk("%s: Too much work in interrupt, status %4.4x.  "
+				   "Disabling functions (%4.4x).\n",
+				   dev->name, status, SetStatusEnb | ((~status) & 0x7FE));
+			/* Disable all pending interrupts. */
+			outw(SetStatusEnb | ((~status) & 0x7FE), ioaddr + EL3_CMD);
+			outw(AckIntr | 0x7FF, ioaddr + EL3_CMD);
+			break;
+		}
+		/* Acknowledge the IRQ. */
+		outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
+
+	} while ((status = inw(ioaddr + EL3_STATUS)) & (IntLatch | RxComplete));
+
+	if (vortex_debug > 4)
+		printk("%s: exiting interrupt, status %4.4x.\n", dev->name, status);
+
+	dev->interrupt = 0;
+	return;
+}
+
+static int
+vortex_rx(struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	int ioaddr = dev->base_addr;
+	int i;
+	short rx_status;
+
+	if (vortex_debug > 5)
+		printk("   In rx_packet(), status %4.4x, rx_status %4.4x.\n",
+			   inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
+	while ((rx_status = inw(ioaddr + RxStatus)) > 0) {
+		if (rx_status & 0x4000) { /* Error, update stats. */
+			unsigned char rx_error = inb(ioaddr + RxErrors);
+			if (vortex_debug > 2)
+				printk(" Rx error: status %2.2x.\n", rx_error);
+			vp->stats.rx_errors++;
+			if (rx_error & 0x01)  vp->stats.rx_over_errors++;
+			if (rx_error & 0x02)  vp->stats.rx_length_errors++;
+			if (rx_error & 0x04)  vp->stats.rx_frame_errors++;
+			if (rx_error & 0x08)  vp->stats.rx_crc_errors++;
+			if (rx_error & 0x10)  vp->stats.rx_length_errors++;
+		} else {
+			/* The packet length: up to 4.5K!. */
+			short pkt_len = rx_status & 0x1fff;
+			struct sk_buff *skb;
+
+			skb = DEV_ALLOC_SKB(pkt_len + 5);
+			if (vortex_debug > 4)
+				printk("Receiving packet size %d status %4.4x.\n",
+					   pkt_len, rx_status);
+			if (skb != NULL) {
+				skb->dev = dev;
+#if LINUX_VERSION_CODE >= 0x10300
+				skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
+				/* 'skb_put()' points to the start of sk_buff data area. */
+				insl(ioaddr + RX_FIFO, skb_put(skb, pkt_len),
+					 (pkt_len + 3) >> 2);
+				outw(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
+				skb->protocol = eth_type_trans(skb, dev);
+#else
+				skb->len = pkt_len;
+				/* 'skb->data' points to the start of sk_buff data area. */
+				insl(ioaddr + RX_FIFO, skb->data, (pkt_len + 3) >> 2);
+				outw(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
+#endif  /* KERNEL_1_3_0 */
+				netif_rx(skb);
+				dev->last_rx = jiffies;
+				vp->stats.rx_packets++;
+				/* Wait a limited time to go to next packet. */
+				for (i = 200; i >= 0; i--)
+					if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+						break;
+				continue;
+			} else if (vortex_debug)
+				printk("%s: Couldn't allocate a sk_buff of size %d.\n",
+					   dev->name, pkt_len);
+		}
+		outw(RxDiscard, ioaddr + EL3_CMD);
+		vp->stats.rx_dropped++;
+		/* Wait a limited time to skip this packet. */
+		for (i = 200; i >= 0; i--)
+			if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+				break;
+	}
+
+	return 0;
+}
+
+static int
+boomerang_rx(struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	int entry = vp->cur_rx % RX_RING_SIZE;
+	int ioaddr = dev->base_addr;
+	int rx_status;
+
+	if (vortex_debug > 5)
+		printk("   In boomerang_rx(), status %4.4x, rx_status %4.4x.\n",
+			   inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
+	while ((rx_status = vp->rx_ring[entry].status) & RxDComplete) {
+		if (rx_status & RxDError) { /* Error, update stats. */
+			unsigned char rx_error = rx_status >> 16;
+			if (vortex_debug > 2)
+				printk(" Rx error: status %2.2x.\n", rx_error);
+			vp->stats.rx_errors++;
+			if (rx_error & 0x01)  vp->stats.rx_over_errors++;
+			if (rx_error & 0x02)  vp->stats.rx_length_errors++;
+			if (rx_error & 0x04)  vp->stats.rx_frame_errors++;
+			if (rx_error & 0x08)  vp->stats.rx_crc_errors++;
+			if (rx_error & 0x10)  vp->stats.rx_length_errors++;
+		} else {
+			/* The packet length: up to 4.5K!. */
+			short pkt_len = rx_status & 0x1fff;
+			struct sk_buff *skb;
+
+			if (vortex_debug > 4)
+				printk("Receiving packet size %d status %4.4x.\n",
+					   pkt_len, rx_status);
+
+			/* Check if the packet is long enough to just accept without
+			   copying to a properly sized skbuff. */
+			if (pkt_len < rx_copybreak
+				&& (skb = DEV_ALLOC_SKB(pkt_len + 2)) != 0) {
+				skb->dev = dev;
+				skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
+				/* 'skb_put()' points to the start of sk_buff data area. */
+				memcpy(skb_put(skb, pkt_len),
+					   bus_to_virt(vp->rx_ring[entry].addr),
+					   pkt_len);
+				rx_copy++;
+			} else{
+				void *temp;
+				/* Pass up the skbuff already on the Rx ring. */
+				skb = vp->rx_skbuff[entry];
+				vp->rx_skbuff[entry] = NULL;
+				temp = skb_put(skb, pkt_len);
+				/* Remove this checking code for final release. */
+				if (bus_to_virt(vp->rx_ring[entry].addr) != temp)
+					printk("%s: Warning -- the skbuff addresses do not match"
+						   " in boomerang_rx: %p vs. %p / %p.\n", dev->name,
+						   bus_to_virt(vp->rx_ring[entry].addr),
+						   skb->head, temp);
+				rx_nocopy++;
+			}
+#if LINUX_VERSION_CODE > 0x10300
+			skb->protocol = eth_type_trans(skb, dev);
+#else
+			skb->len = pkt_len;
+#endif
+			netif_rx(skb);
+			dev->last_rx = jiffies;
+			vp->stats.rx_packets++;
+		}
+		entry = (++vp->cur_rx) % RX_RING_SIZE;
+	}
+	/* Refill the Rx ring buffers. */
+	for (; vp->dirty_rx < vp->cur_rx; vp->dirty_rx++) {
+		struct sk_buff *skb;
+		entry = vp->dirty_rx % RX_RING_SIZE;
+		if (vp->rx_skbuff[entry] == NULL) {
+			skb = dev_alloc_skb(PKT_BUF_SZ);
+			if (skb == NULL)
+				break;			/* Bad news!  */
+			skb->dev = dev;			/* Mark as being used by this device. */
+#if LINUX_VERSION_CODE > 0x10300
+			skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
+			vp->rx_ring[entry].addr = virt_to_bus(skb->tail);
+#else
+			vp->rx_ring[entry].addr = virt_to_bus(skb->data);
+#endif
+			vp->rx_skbuff[entry] = skb;
+		}
+		vp->rx_ring[entry].status = 0;	/* Clear complete bit. */
+	}
+	return 0;
+}
+
+static int
+vortex_close(struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	int ioaddr = dev->base_addr;
+	int i;
+
+	dev->start = 0;
+	dev->tbusy = 1;
+
+	if (vortex_debug > 1) {
+		printk("%s: vortex_close() status %4.4x, Tx status %2.2x.\n",
+			   dev->name, inw(ioaddr + EL3_STATUS), inb(ioaddr + TxStatus));
+		printk("%s: vortex close stats: rx_nocopy %d rx_copy %d"
+			   " tx_queued %d.\n",
+			   dev->name, rx_nocopy, rx_copy, queued_packet);
+	}
+
+	del_timer(&vp->timer);
+
+	/* Turn off statistics ASAP.  We update lp->stats below. */
+	outw(StatsDisable, ioaddr + EL3_CMD);
+
+	/* Disable the receiver and transmitter. */
+	outw(RxDisable, ioaddr + EL3_CMD);
+	outw(TxDisable, ioaddr + EL3_CMD);
+
+	if (dev->if_port == XCVR_10base2)
+		/* Turn off thinnet power.  Green! */
+		outw(StopCoax, ioaddr + EL3_CMD);
+
+#ifdef SA_SHIRQ
+	free_irq(dev->irq, dev);
+#else
+	free_irq(dev->irq);
+	irq2dev_map[dev->irq] = 0;
+#endif
+
+	outw(SetIntrEnb | 0x0000, ioaddr + EL3_CMD);
+
+	update_stats(ioaddr, dev);
+	if (vp->full_bus_master_rx) { /* Free Boomerang bus master Rx buffers. */
+		outl(0, ioaddr + UpListPtr);
+		for (i = 0; i < RX_RING_SIZE; i++)
+			if (vp->rx_skbuff[i]) {
+#if LINUX_VERSION_CODE < 0x20100
+				vp->rx_skbuff[i]->free = 1;
+#endif
+				dev_kfree_skb (vp->rx_skbuff[i], FREE_WRITE);
+				vp->rx_skbuff[i] = 0;
+			}
+	}
+	if (vp->full_bus_master_tx) { /* Free Boomerang bus master Tx buffers. */
+		outl(0, ioaddr + DownListPtr);
+		for (i = 0; i < TX_RING_SIZE; i++)
+			if (vp->tx_skbuff[i]) {
+				dev_kfree_skb(vp->tx_skbuff[i], FREE_WRITE);
+				vp->tx_skbuff[i] = 0;
+			}
+	}
+
+	MOD_DEC_USE_COUNT;
+
+	return 0;
+}
+
+static struct enet_statistics *
+vortex_get_stats(struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	unsigned long flags;
+
+	if (dev->start) {
+		save_flags(flags);
+		cli();
+		update_stats(dev->base_addr, dev);
+		restore_flags(flags);
+	}
+	return &vp->stats;
+}
+
+/*  Update statistics.
+	Unlike with the EL3 we need not worry about interrupts changing
+	the window setting from underneath us, but we must still guard
+	against a race condition with a StatsUpdate interrupt updating the
+	table.  This is done by checking that the ASM (!) code generated uses
+	atomic updates with '+='.
+	*/
+static void update_stats(int ioaddr, struct device *dev)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+
+	/* Unlike the 3c5x9 we need not turn off stats updates while reading. */
+	/* Switch to the stats window, and read everything. */
+	EL3WINDOW(6);
+	vp->stats.tx_carrier_errors		+= inb(ioaddr + 0);
+	vp->stats.tx_heartbeat_errors	+= inb(ioaddr + 1);
+	/* Multiple collisions. */		inb(ioaddr + 2);
+	vp->stats.collisions			+= inb(ioaddr + 3);
+	vp->stats.tx_window_errors		+= inb(ioaddr + 4);
+	vp->stats.rx_fifo_errors		+= inb(ioaddr + 5);
+	vp->stats.tx_packets			+= inb(ioaddr + 6);
+	vp->stats.tx_packets			+= (inb(ioaddr + 9)&0x30) << 4;
+	/* Rx packets	*/				inb(ioaddr + 7);   /* Must read to clear */
+	/* Tx deferrals */				inb(ioaddr + 8);
+	/* Don't bother with register 9, an extension of registers 6&7.
+	   If we do use the 6&7 values the atomic update assumption above
+	   is invalid. */
+	inw(ioaddr + 10);	/* Total Rx and Tx octets. */
+	inw(ioaddr + 12);
+	/* New: On the Vortex we must also clear the BadSSD counter. */
+	EL3WINDOW(4);
+	inb(ioaddr + 12);
+
+	/* We change back to window 7 (not 1) with the Vortex. */
+	EL3WINDOW(7);
+	return;
+}
+
+/* This new version of set_rx_mode() supports v1.4 kernels.
+   The Vortex chip has no documented multicast filter, so the only
+   multicast setting is to receive all multicast frames.  At least
+   the chip has a very clean way to set the mode, unlike many others. */
+static void
+set_rx_mode(struct device *dev)
+{
+	int ioaddr = dev->base_addr;
+	short new_mode;
+
+	if (dev->flags & IFF_PROMISC) {
+		if (vortex_debug > 3)
+			printk("%s: Setting promiscuous mode.\n", dev->name);
+		new_mode = SetRxFilter|RxStation|RxMulticast|RxBroadcast|RxProm;
+	} else	if ((dev->mc_list)  ||  (dev->flags & IFF_ALLMULTI)) {
+		new_mode = SetRxFilter|RxStation|RxMulticast|RxBroadcast;
+	} else
+		new_mode = SetRxFilter | RxStation | RxBroadcast;
+
+	outw(new_mode, ioaddr + EL3_CMD);
+}
+
+#ifdef MODULE
+void
+cleanup_module(void)
+{
+	struct device *next_dev;
+
+	/* No need to check MOD_IN_USE, as sys_delete_module() checks. */
+	while (root_vortex_dev) {
+		next_dev = ((struct vortex_private *)root_vortex_dev->priv)->next_module;
+		if (root_vortex_dev->dma)
+		  free_dma(root_vortex_dev->dma);
+		unregister_netdev(root_vortex_dev);
+		outw(TotalReset, root_vortex_dev->base_addr + EL3_CMD);
+		release_region(root_vortex_dev->base_addr, CORKSCREW_TOTAL_SIZE);
+		kfree(root_vortex_dev);
+		root_vortex_dev = next_dev;
+	}
+}
+#endif /* MODULE */
+
+/*
+ * Local variables:
+ *  compile-command: "gcc -DMODULE -D__KERNEL__ -Wall -Wstrict-prototypes -O6 -c 3c515.c"
+ *  c-indent-level: 4
+ *  tab-width: 4
+ * End:
+ */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov