patch-1.3.49 linux/drivers/char/scc_config.h

• Lines: 70
• Date: Thu Jan 1 02:00:00 1970
• Orig file: v1.3.48/linux/drivers/char/scc_config.h
• Orig date: Sun Sep 3 12:26:53 1995

diff -u --recursive --new-file v1.3.48/linux/drivers/char/scc_config.h linux/drivers/char/scc_config.h
@@ -1,69 +0,0 @@
-#include <linux/scc.h>
-
-/********* CONFIGURATION PARAMATERES; PLEASE CHANGE THIS TO YOUR OWN SITUATION **********/
-
-/* SCC hardware parameters */
-
-/* use the following board types: 
- *
- *	PA0HZP		OptoSCC (PA0HZP)
- *	EAGLE         	EAGLE
- *	PC100         	PC100 
- *	PRIMUS        	PRIMUS-PC (DG9BL)
- *	DRSI          	DRSI PC*Packet
- *	BAYCOM        	BayCom (U)SCC
- *	
- */
-
-int     Nchips	     = 2	; /* number of chips */
-io_port Vector_Latch = 0	; /* addr. of INTACK-Latch (0 for poll mode) */
-int     Ivec	     = 7	; /* interrupt vector */
-long    Clock	     = 4915200	; /* frequency of the scc clock */
-char	Board	     = BAYCOM	; /* what type of SCC card do you use? */
-int	Option	     = 0	; /* command for extra hardware */
-io_port Special_Port = 0	; /* port address for special hardware */
-				  /* (for EAGLE, PC100, PRIMUS, DRSI) */
-
-			/*      ^  never remove the semicolon !! */
-			
-
-
-/* 			Channel    A      B	    Chip	*/
-/*			         ============	  ========	*/
-/* Control ports:						*/
-
-io_port SCC_ctrl[MAXSCC * 2] = 	{0x304, 0x305,  /* ...one... 	*/
-				 0x306, 0x307,  /* ...two...	*/
-				     0,     0,  /* ...three...	*/
-				     0,     0}; /* ...four...	*/
-
-/* Data ports:							*/
-
-io_port SCC_data[MAXSCC * 2] =  {0x300, 0x301,	/* ...one...	*/
-				 0x302, 0x303,	/* ...two...	*/
-				     0,     0,	/* ...three...	*/
-				     0,     0};	/* ...four...	*/
-
-
-/* set to '1' if you have and want ESCC chip (8580/85180/85280) support */
-
-/*					      Chip	*/
-/*				            ========   	*/
-int SCC_Enhanced[MAXSCC] =	{0,	/* ...one...	*/
-				 0,  	/* ...two...	*/
-				 0,  	/* ...three...	*/
-				 0};	/* ...four...	*/
-
-/* some useful #defines. You might need them or not */
-
-#define VERBOSE_BOOTMSG 1
-#undef  SCC_DELAY		/* perhaps a 486DX2 is a *bit* too fast */
-#undef  SCC_LDELAY		/* slow it even a bit more down */
-#undef  DONT_CHECK		/* don't look if the SCCs you specified are available */
-#define DO_FAST_RX		/* experimental timer routine called immediateley */
-				/* after every received frame */
-
-
-/* The external clocking, nrz and fullduplex divider configuration is gone */
-/* you can set these parameters in /etc/z8530drv.rc and initialize the  */
-/* driver with sccinit */